Xerox 6110MFP and Snow Leopard - WORKS!

I had a friend install Snow Leopard, Apples new Operating System.
It killed his Xerox MFP 6110 Machine.

I make this long story very short.

Leave the current printer in the system.
Go add the printer again, this time making a NEW QUEUE for that printer using the OLD driver. This is the final resolution to making my Xerox 6110 MFP work correctly.
Once I had this working, I shared it out on the network and the rest of the 10.6 computers could print without any problems.

When recreating the printer - it kept using the same queue which led me to believe it was using the old or incorrect driver - this is why I say make a new queue with the old driver - as it showed the original driver as the one being used - and it worked like a champ. It would auto-add the other printer on reboot, although it still would not print correctly. Something to do with the specific Queue itself.

This is what I had done previous to the above mentioned:

It did not like the drivers previously installed and would not print.

I deleted all the printers, readded the printer using the built in driver (appears it copied it over from OSX 10.5 into 10.6, although the first time you check yoru printer - it tells you that it needs an updated printer driver).

I followed the steps here:
http://techblog.lucidillusion.org/2009/09/04/xerox-phaser-6120-on-mac-os-x-10-6-snow-leopard/

You will have to goto the website listed and download the custom PPD driver.
Once you have downloaded this, make sure its somewhere you can find it - and if Safari or anything else appended a .TXT to it, take it off.

Go back to add a new printer, this time after it tries to autoselect the printer, change it and go load the custom PPD you just downloaded.

I did notice that the icon of the printer changed and that it does print a little different - but all appears to be working as it should.

When recreating the printer - it kept using the same queue which led me to believe it was using the old or incorrect driver - this is why I say make a new queue with the old driver - as it showed the original driver as the one being used - and it worked like a champ. It would auto-add the other printer on reboot, although it still would not print correctly. Something to do with the specific Queue itself.


IF NONE OF THIS FIXES YOUR PROBLEM...
I suggest trying to install the Rosetta app that comes on the Snow Leopard DVD.
Follow the threads on Apple or do a google search on it.

This is the original Apple thread I was reading:
http://discussions.apple.com/thread.jspa?threadID=2144674&tstart=1

PMU Shutdown Cause -122

Is your Apple Xserve Server going down at random with a "cause code" of -122 from the PMU?

I had done a little digging after one of our servers kept going down without any reason and no warning.

To make a long story short - check to see if you have a UPS (APC or otherwise) plugged into the Server - either USB or Serial (most likely USB) - unplug that and see if it helps.

For some reason - from what I read, the UPS sends out incorrect information about its runtime - or the server cant' think it can run in that allotted time so it just shuts off. Not a shutdown, a "pulled the power plug" kinda off.

Sync iCal and iPhone with Google Calander

Since I left my last position where we had an Exchange server setup to sync all our stuff... well, now that I do not have that - I will want the functionality on a personal level... which I found out Google can help you accomplish this...


The process is very straight forward... I will try to add pictures later.
Including links from Gmail Support for setting these devices up...

First things first - you need to make sure you have your Google calendar setup and ready to go -if you do not have a Google account - or checked your calendar, I suggest you do that before continuing on.

Instructions from Google:
http://www.google.com/support/calendar/bin/answer.py?answer=99358#ical

To get the iCal in OSX to work right - we add the following info into iCal:
Preferences > Accounts - Create a new account - name it Gmail or something similar.
Your username and password are as follows:
Username: user@gmail.com
Password: your password
Click the down-arrow and fill in the selected URL for the calendar server:
https://www.google.com/calendar/dav/@gmail.com/user

Once this is done, iCal will go sync with Google - if there is anything in there to sync.

To get the iPhone working - you have to set it up as an Exchange Account - and on iPhones, since you are only allowed a single Exchange account - if you use it for work and using Exchange - this might not work for you.

To get this done on your iPhone, follow these steps.
http://www.google.com/support/mobile/bin/answer.py?hl=en&answer=138740

If you need help, message me.
One thing to note, when entering your user/password, the username is always user@gmail.com - they showed user@googlemail.com and I kept getting bad password responses.

So far its working great - is quick to update. If you are running Entourage - you can set it to sync with iCal so you can have those dates transferred to your phone/Google calender as well.

Don't try to setup mail when setting up the iPhone - the only thing Google allows is Contacts and Calenders.

Next Up: Hamachi VPN for Remote Control through VPN

Fans Running At Warp Speed + CPU at Max Temp!

Have you had any of your Mac's exhaust fans just start running as fast as they could along with a processor that you could cook eggs on? While at idle/fresh reboot/restart?

My MacBook experienced this phenomena and it stuck with it - almost to the point of making me reload the OS.
I did a quick Google search and found that the PMU (Power Management Unit) gets goofy and can make the fans run at top speed, which is about 6800rpm, average at idle is 1800rpm.

As I explained to a friend, Mac's will do their suspend/reanimation with no problems - it works and is more than you can say for its Windows counterpart which will constantly hang, memory exceptions, application failures, lockups - you just have to reboot after suspending much with Windows - but Mac works, you just have to reset its brain once in a while...

While this was going on, it also made my CPU heat up as hot as it could get - thus turning the fans on in my presumption, but resetting the PMU fixed all the issues I had hat hand.

To reset the PMU in the newer MacBooks, just remove the battery/ac adapter and hold the power button down for 5-10 seconds. The second step (which wasn't listed for MacBooks) was to hold Option+Command+P+R and hit the power button (with batter/ac attached) - it will reboot twice and hopefully all will be good to go.

Heres the Apple Doc I read/used:
Apple - http://support.apple.com/kb/HT1411

External Booting

I've been playing with Imaging utilities for Mac. Specifically for OSX 10.5.x.
We have a OSX Server at the Office where I work. Its just a Mac Mini loaded with OSX Server, which at the time is all unplugged sitting in a pile on the floor. Just before it got moved out of the "lab" and into the "conference room" which is now our Lab because we're hiring another person to help us out.

Anyways - long story short.
I used Carbon Copy to image the complete Server via Firewire Targeted Mode (I put the Mini in Targeted Mode) and used a Firewire Cable to my MacBook, which I use a USB to SATA Adapter to which I copied the image to a 2.5" 250gig Laptop SATA Drive. Could have as well been my iPod... I just had the 250gig laying around, why not use it? My iPod is only 4gigs anyways.

I brought the image home, hooked the USB to SATA adapter up to the MacBook, booted holding Option (gives you boot menu) and it will automatically find the USB Adapter and allow you to boot from the external drive just as if it was your internal hard drive.
If you image another persons machine, you will need to know their passwords in order to perform anything. You can reset them if you don't know how but all in all - this is a very easy way to replicate your drive as a backup drive and boot from it - from any mac.

The simple thing would be have an external usb hard drive, image your drive to it (using another computer to pull it from your drive and to the external) then you can take your data/programs/preferences/everything with you anywhere you go...

syslogd using all resources in osx

Has your computer hung up with 'syslogd' using 99% of your resources?
You kill it only to have it come alive again and use every bit of your resources?

I had this problem, couldn't find a direct fix, so I am posting my solution.
Part of this came from a fellow on Apples discussion pages, credit given at botton.

I am going to make this short and sweet. Cut and paste if you wish.

--begin fix--
It turns out a very large /var/log/asl.db (a primary log for syslogd) causes all manner of issues, notably, occasional syslogd cpu hoggage. In my case, I was getting repeated malloc errors from syslogd as well, compounding the issue. My asl.db was was 55Mb. After reading this blog post:

http://smartic.us/2007/11/8/leopard-100-cpu-usage-caused-by-syslogd-and-possibly-time-machine

I went on a hunt, and found, according to:

http://developer.apple.com/documentation/Darwin/Reference/ManPages/man8/syslogd.8.html

The asl.db size is supposed to be limited to a default of 25600000 bytes. Mine was way bigger. Something was clearly amiss.
There is no database size limit -- theoretically anyway; practically, there clearly is, as evidenced by this and many similar threads around the net.

The fix is to edit /System/Library/LaunchDaemons/com.apple.syslogd.plist

and add the db_max arg:

/usr/sbin/syslogd
-db_max 5000000

Adjust the max to your taste. I limited mine to 5M bytes. After that, the nightly sweep should keep this problem from occurring again.
I also deleted my asl.db file, which is located in /private/var/log - See *Note below.

To stop and restart 'syslogd' server, type/paste in terminal:

sudo launchctl unload /System/Library/LaunchDaemons/com.apple.syslogd.plist
*See Note Below
sudo launchctl load /System/Library/LaunchDaemons/com.apple.syslogd.plist

*Note: As a precaution, I backed up my asl.db file and deleted the original before starting the service. If you want to perform this, type the following in terminal:

sudo cp /private/var/log/asl.db /private/var/log/asl.bak
Now continue with the 'load' command to restart the 'syslogd' service.
--end fix--

Most credit given to:
adhir

Posts: 1
From: Washington, DC Metro
Registered: Nov 27, 2007

http://discussions.apple.com/thread.jspa?threadID=1228710